xsvast.blogg.se

1. ROSS CARBONITE BLACK 2 720P
2. ROSS CARBONITE BLACK 2 GENERATOR
3. ROSS CARBONITE BLACK 2 SERIAL
4. ROSS CARBONITE BLACK 2 FULL

ROSS CARBONITE BLACK 2 GENERATOR

ROSS CARBONITE BLACK 2 720P

Standard System Includes: 36 Inputs & 25 outputs in 3G 9 Inputs 12G 12G SDI, Quad 2SI, Quad SQD, 1080p, 1080i, and 720p 5 Outputs in UHD 3x12G SDI/Quad 2SI/Quad SQD and 2x2SI.

ROSS CARBONITE BLACK 2 SERIAL

12 Multi-Definition Serial Digital Inputs, 1 HDMI Inputs, 1 Reference input.TSL UMD v3.1 Serial Tally Protocol Transmit and v3.1 Receive with Bus Messages.Audio Mixer Control (Yamaha 01V96 and DM1000).Video Server Control (AMP) with Ross Video Exclusive Roll Clip function.Robotic Camera Control (VISCA, Canon BU and Ross Cambot).Single MultiViewer with up to 10 Source Displays, Multiple Layouts with Tally, Label controls and Clock.

ROSS CARBONITE BLACK 2 FULL

1 Full ME’s with 5 keys (4 full function + 1 transition keyer for DVE and media transitions) plus 2 floating MiniME’s each with 2 Keyers.13 Inputs (12 SDI and 1 HDM)I & 6 outputs (5 SDI and 1 HDMI).On Panel Menu with Support for DashBoard GUI Menu as well.Legendary Ross Fader Bar (Lifetime Warranty on Faders!!).Full Next Transition Area with Ross Video exclusive Roll Clip Function.9 XPTs for BKGD, PST and KEY/AUX/CC BUSes.Solo 13 gives you more I/O to work with in your productions, while retaining that compact Carbonite Black Solo form factor. The Carbonite supports TSL and UMD as well and those can be configured from the add device menu.The Ross Video Carbonite Black Solo13 / 13-Input / 6 Output, 1 M/E Video Production Switcher is a self-contained production switcher and hardware panel combination with 13 inputs and 6 outputs. Ross is like Grass in that tally is usually configured across several different sub-menus on different pages, the "Tally" menu is only one of them. Tally can be a a real pain to troubleshoot because it can be connected correctly but the logic isn't correct so it doesn't trigger. Not to say that the GPIO doesn't need to be configured correctly so here are those links.īeyond that the On-Air status of each input must be correctly configured so that it sends voltage when it's supposed to. Apparently the fiber converter piggybacks the tally (and com) data on the ANC data portion of this signal for camera control. If you read down to the bottom of the following link Gary Adams states that there must be video present on the 1st input of the fibre converter even if you are not using an Atem. I believe the GPIO pins can be configured to output tally information with a high level of 5V and low of 0V, so it's possible you could use this as an alternative to the dedicated tally port. It seems like most of the Carbonite switchers also have GPIO ports that are separate from the dedicated tally outputs.

Since the Studio Fiber Converter expects a 5-24V input to indicate when tally is active, you'll probably have to provide a voltage source in this range to get things to work (along with a pull-up or pull-down resistor depending on how you wire things). Many of the Sony CCU units work with a simple contact closure input so they could probably be wired directly to the Carbonite's tally output. Looking at the Ross Carbonite documentation it seems like the tally port just works using contact closures, so the individual tally pins are connected to the common pins when the tally is active and disconnected otherwise. Are you sure that the tally connections of the Ross Carbonite are passive? It seems like the switcher has to do the signaling, so I'm not sure how it can just passively wait for signals from another device.